Locatie van firmware voor DV7001?

Gestart door peterbr, februari 19, 2011, 17:14:26

Vorige topic - Volgende topic

0 leden en 1 gast bekijken dit topic.

peterbr

Weet iemand een download locatie voor de laatste FW voor de DV7001?

Lijkt erop dat Marantz alle verwijzingen naar DV7001 vab hun websites verwijdert heeft.
SR7001, DV7001, LINN Komponent Speakers, DM8000, Sonos ZP90

Vlearmoes

Alleen via de service centers te doen  :yes:
Integra DTR 9.9 & Audyssey MultEQ XT Pro | Marantz BD8002 | Panasonic 50PV20 | Technisat Multytenne & HD S2 plus | Kef Reference series Model Three, Model 200, Calinda| Synlogy 110j  Asus G50v

Stadium III

DV 7001 was wel te oen aan huis
V09 was iig de laaste en loste HDMI problemen op
Marantz SR 8012 Klipsch atmos setup

5.2.4

drees62

Citaat van: Stadium III op februari 19, 2011, 19:21:19
DV 7001 was wel te oen aan huis
V09 was iig de laaste en loste HDMI problemen op

Ik heb die laatste versie nog wel als zip-bestand. Stuur me maar even een PM dan zal ik 'm naar je emailen.
Bestand even branden op CD-ROM en hoppa!  :-D

Hieralvast de procedure:

Procedure:
•Download the file DV7001.bin
•Burn this file on a data CD-R (adjust the burn program so, that only one
recording is possible on this disc, in other words "close session", file format is iSO9660 and Write Format DISC AT ONCE)
Important: During the below mentioned procedure, do not switch off the set or
disconnect the mains cable from the set unless noticed. This will interrupt the
upload process and damage the DVD player. This is not covered by warranty.
•Connect the DVD player to a display unit (e.g. Television set)
•Switch ON the DVD player.
•Open the tray by pressing the OPEN/CLOSE button
•Put the data CD-R on the DVD tray.
•Close the DVD tray.
•The CD-R will be red and "LOAD" is displayed on the DVD front panel. (and "Loading" on the display unit)
•The display unit shows: "UPGRADE FILE DETECTED" and "FILE COPING" (very short) and next the message "FILE COPING" will be changed to: "UPGRADING"
•The tray opens automatically (DO NOT SWITCH OFF THE SET).
•Remove now the CD-R from the tray (tray will stay open).
•The display of the DV7001 will show "ERASE" and this will change to
"WRITE" (display unit will still show "UPGRADE FILE DETECTED
UPGRADING"). This takes about 90 seconds.
•After that the display of the DV7001 will show "UPG END"
•Now the DVD player will be resetted and the tray will be closed automatically.
•Press the POWER button to switch off the set. (the set is now upgraded)

Checking if the upgrade is done successfully:
•Leave the DVD player connected to the display unit.
•Press the POWER button to switch ON the unit.
•Open the tray by pressing the OPEN/CLOSE button.
•Press the button DISP on the remote control of the DVD player.
•Make sure that the text "V09" is present in the following line, displayed on the display unit: DV7001 V09 V701-12 3

stef032

Citaat van: drees62 op februari 25, 2011, 20:43:25
Ik heb die laatste versie nog wel als zip-bestand. Stuur me maar even een PM dan zal ik 'm naar je emailen.
Bestand even branden op CD-ROM en hoppa!  :-D

Hieralvast de procedure:

Procedure:
•Download the file DV7001.bin
•Burn this file on a data CD-R (adjust the burn program so, that only one
recording is possible on this disc, in other words "close session", file format is iSO9660 and Write Format DISC AT ONCE)
Important: During the below mentioned procedure, do not switch off the set or
disconnect the mains cable from the set unless noticed. This will interrupt the
upload process and damage the DVD player. This is not covered by warranty.
•Connect the DVD player to a display unit (e.g. Television set)
•Switch ON the DVD player.
•Open the tray by pressing the OPEN/CLOSE button
•Put the data CD-R on the DVD tray.
•Close the DVD tray.
•The CD-R will be red and "LOAD" is displayed on the DVD front panel. (and "Loading" on the display unit)
•The display unit shows: "UPGRADE FILE DETECTED" and "FILE COPING" (very short) and next the message "FILE COPING" will be changed to: "UPGRADING"
•The tray opens automatically (DO NOT SWITCH OFF THE SET).
•Remove now the CD-R from the tray (tray will stay open).
•The display of the DV7001 will show "ERASE" and this will change to
"WRITE" (display unit will still show "UPGRADE FILE DETECTED
UPGRADING"). This takes about 90 seconds.
•After that the display of the DV7001 will show "UPG END"
•Now the DVD player will be resetted and the tray will be closed automatically.
•Press the POWER button to switch off the set. (the set is now upgraded)

Checking if the upgrade is done successfully:
•Leave the DVD player connected to the display unit.
•Press the POWER button to switch ON the unit.
•Open the tray by pressing the OPEN/CLOSE button.
•Press the button DISP on the remote control of the DVD player.
•Make sure that the text "V09" is present in the following line, displayed on the display unit: DV7001 V09 V701-12 3

stef032

Hoi,
Zit zelf onm de firmware V09 van de DV7001 zou je mij de zip of link naar zip willen mailen op ej,steffers@quicknet.nl bijvoorbaat dank

Eric-Jan

drees62

Citaat van: stef032 op juni 07, 2011, 01:50:03
Hoi,
Zit zelf onm de firmware V09 van de DV7001 zou je mij de zip of link naar zip willen mailen op ej,steffers@quicknet.nl bijvoorbaat dank

Eric-Jan

V09 is volgens mij de laatste versie, nieuwer heb ik igg niet